|
|
|
|
|
|
|
|||
|
|
|
||
|
|
|
|
|
|
|
|||
 |
 |
 |
 |
 |
 |
 |
|||||||||||||||||
|
Accessories | |||||||||||||||||||||||
|
Aluminum Chute Has a flared end and curled top for added strength. Cross braces are steel pipe (easy on the hands). 1000 lb. test chain encircles chute for hanging purposes.
|
Porta Chute Hooks to ready-mix chute. Has 12 diameter elephant trunk 66 long, with a handle attached. Part No. FAC 
|
||||||||||||||||||||||
|
Chute Hanger with Hooks and Chain Hooks onto floor joist to suspend chute. Does not damage floor joist. Part No. CH 
|
Wall Slider Slides forms for squaring wall. Two required. At bottom of forms, pin one to outside and one to inside. Place 2x4 under slider. On cadence count, pry both up. Both inside and outside forms move together. Prevents ties from bending. Note: If only one wall is moved the tie bends, which can cause wall blowout. Part No. WS 
|
||||||||||||||||||||||
|
Tie Clamp Used to secure objects in forms without nailing. Select a form slightly wider than the object being installed. Make sure object is same thickness as wall. If pouring an 8 wall, pin a 10 tie on each side of object. The 10 tie will protrude outside the form. Pin and wedge the tie clamp onto the protruding ties. Place a wedge (flat) across the edge of both adjoining forms under the bolt of the tie clamp. Turn handle to tighten the forms. Object will be secure between the forms. Always plumb and brace the object. Part No. TC 
|
Pour Shield Sets over the top of form and deflects ready-mix flow down into the forms. Keeps concrete from spilling over. Part No. PS 
|
||||||||||||||||||||||
|
Turnbuckle Wall Aligner Pins to form near top. 2x4 lumber is nailed to the brace and staked to the ground. Turn brace, and wall will be pushed out or pulled in. Part No. TBWB 
|
Aluminum Turnbuckle
|
||||||||||||||||||||||
|
Tie Break-Off Tool Tool fits over tie. Push tool up or down to break tie. Helps when a deep break back is required. Part No. BOT 
|
Aluminum Stiff Back for Lumber Pins to side rail of forms. Nail two-by lumber through holes provided in the bracket. Provides a rigid lumber extension to aluminum forms. Part No. ASB 
|
||||||||||||||||||||||
|
Post Footing Form Aluminum form is 8 high and 30 in diameter. Two pieces assemble with pins and wedges. Quick assembly and stripping. Place a stake in center of footing, and put nail in stake for elevation. Several forms nest together for transport. Other sizes by request. Part No. PFF 
|
Form Puller (Pair) Aids removal of first form in a confined area such as the inside of a porch. There is a right and left puller. Place pin of tool into the bushings of form to be stripped. Pull down. Form will be forced away from the wall. Part No. FP2 
|
||||||||||||||||||||||
|
Stake Puller Helps in pulling steel stakes. Part No. 135 
|
Tie Puller Used with special ties. Hook fits through hole. Sliding weight strikes against handle and pulls tie out. Part No. TP 
|
||||||||||||||||||||||
|
Wall Puller Used to square set-up forms. Part No. WP 
|
EZ Brick Corner Puller Used to strip Brick inside corners. First, break-off ties on both sides of the corner, grasp handle with one hand, place opposite end into corner, and turn one quarter turn. Strike weight against handle; corner will jar straight out from corner without damaging brick surface. Part No. EZ Corner 
|
||||||||||||||||||||||
|
Aluminum Wall Shovel This lightweight shovel sits inside the form and keeps concrete moving efficiently. Part No. WASH 
|
Beam Pocket (8 angled shown) Made to customersspecifications. Available with angled top for easy clamping to the top of forms. Part No. BP 
|
||||||||||||||||||||||
|
Dump Box (All steel product. Shown painted for photo.) Ready-mix pours directly into dump box. Concrete is directed down, and there is no overflow. Part No. DB 
|
Line Stretcher Thumb screws clamp unit to top of form. Provides post over form edge for attaching line of string. Part No. LS 
|
||||||||||||||||||||||
|
Extension Bracket Pins to top of form when a higher wall is needed. Two-by lumber is nailed to bracket flush with form. Part No. EXB 
|
Aluminum Ledge Bracket Pins to top of form. Provides nailer for brick ledge. Part No. ALB 
|
||||||||||||||||||||||
|
Ledge Bracket 2 x 4 Used when forming deep brick ledge with aluminum forms. Example: If an 8 high, 10 thick wall requires a 4 brick ledge 4 deep, install an 8 form inside and a 4 form outside using 10 ties. Pin ledge bracket to top of 4 form. Set top 4 form on bracket using 6 ties. Must nail a 2 x 4 on edge through the nail hole provided in the bracket. The 2 x 4 blocks off the remaining gap, providing a 4 wide brick seat. Other ledge depths can be formed using proper form combinations. Part No. 2x4LB 
|
6-8-10 Top Spacer Pinned across top of form to accurately space forms. Specify full or nominal. Various sizes available. Part No. 6-8-10 TS 
|
||||||||||||||||||||||
|
Water Stop Helps prevent water from entering through control joints. Part No. MWS 
|
Adjustable Door Block Down Part No. AADB 
|
||||||||||||||||||||||
|
Aluminum Door Block Out Specify door width. Part No. AADB 
|
Footing Tamper Used to tamp fresh poured concrete in footings. Part Nos. 4 Tamper FTAMPER-4 5 Tamper FTAMPER-5 6 Tamper FTAMPER-6 
|
||||||||||||||||||||||
|
Laser Rod Supports laser levels. Part Nos. 4 4 ROD 5 5 ROD 6 6 ROD 8 8 ROD 
|
Scraper Long handle scraper, used to clean the face sheets of panels. Part No. CC214 
|
||||||||||||||||||||||
|
Hand Scraper Double-edged solid carbine scraper used to clean side rails of panels. Part No. HWS 
|
Come Along Used to move concrete. Part No. CC905 
|
||||||||||||||||||||||
|
Rebar Cutter and Bender Part No. GG725 
|
Anchor Bolt
|
||||||||||||||||||||||
|
Tie Twister Used for bag ties. Part No. 09312 
|
Cement Nails
|
||||||||||||||||||||||
|
#8 Duplex 50# Nails Part No. 8-DH 
|
Aluminum Angle Clip Used for nailing two-by lumber on top of forms. Part No. AAC 
|
||||||||||||||||||||||
|
Form Stake
|
Rebar Stake
|
||||||||||||||||||||||
|
Round Stake Part Nos. 3/4 x 12 3/4x12 DNS 3/4 x 18 3/4x18 DNS 3/4 x 24 3/4x24 DNS 3/4 x 30 3/4x30 DNS 3/4 x 36 3/4x36 DNS 3/4 x 48 3/4x48 DNS 7/8 x 18 7/8x18 DNS 7/8 x 24 7/8x24 DNS 7/8 x 30 7/8x30 DNS 7/8 x 36 7/8x36 DNS 7/8 x 48 7/8x48 DNS 
|
Bushing Tightener Punch Used with Bushing Back-up Block to tighten bushings in panels. Part No. BUSHING TOOL 
|
||||||||||||||||||||||
|
Bushing Back-up Block Used with Bushing Tightener Punch to tighten bushings in panels. Part No. BB 
|
Rebar Chair Piece Part Nos. 2 Bar RC-6-2 3 Bar RC-12-3 
|
||||||||||||||||||||||
|
Sump Crock Part No. PLASTIC 
|
Footing Keyway Screed Forms keyways to lock poured walls into the footings. Part No. FKS 
|
||||||||||||||||||||||
|
Stringlinerฎ 250 feet of #18 braided nylon. in fluorescent pink, green or orange. Stringlinerฎ is a registered trademark of Stringliner Company.
|
100 Nylon Coated Steel Blade Measuring Tape Part No. NR 18100 
|
||||||||||||||||||||||
|
200 Nylon Coated Steel Blade Measuring Tape Part No. NR 18200 
|
Little Giant Chalk Reel 100 heavy-duty cord and pull ring. Hooks easily to a utility belt and holds almost 1 lb. of chalk. One-piece steel crank for extra-long life. Part No. GB1NEON 
|
||||||||||||||||||||||
|
Ultra-Mark Fluorescent Spray Available in blue or red-orange
|
Marking Chalk 8 oz. bottle
|
||||||||||||||||||||||
|
Ultra-Fine Chalk 5 lbs.
|
Hinged Bell Trap Part Nos. 4x 4 4x4 HBT 6x 6 6x6 HBT  Gloves Part No. BJG 
|
||||||||||||||||||||||
|
Durand Supreme Form Release Oil, 55 gallons Form release agent. Part No. RS-55 
|
Durand Supreme Form Release Oil, 275 gallons Form release agent. Part No. OTS 
|
||||||||||||||||||||||
|
20-Gallon Oil Sprayer One charge of air empties tank. Oil level sight gauge and oil pressure gauge. Oil filter removes debris. Part No. 20 GAL AFO 
|
60-Gallon Oil Sprayer One charge of air empties tank. Oil level sight gauge and oil pressure gauge. Oil filter removes debris. Part No. 60 GAL AFO 
|
||||||||||||||||||||||
|
60-Gallon Oil Sprayer with Hose Reel One charge of air empties tank. Oil level sight gauge and oil pressure gauge. Oil filter removes debris. Hose reel attached. Part No. 60 GAL AFO with hose reel 
|
Barrel Pump For use with 55-gallon form oil drums. Part No. BARREL PUMP 
|
||||||||||||||||||||||
|
Chapin™ Concrete Hand Sprayer Commercial quality. Has oil-resistant seals. ChapinTM is a trademark of Chapin Manufacturers. Part No. CHAPIN 
|
Q2 Form Release Oil, 55-Gallon Drum Environmentally safe form release agent. Part No. Q2 55 
|
||||||||||||||||||||||
|
Q2 Form Release Oil, 275 Gallons Environmentally safe form release agent. Part No. OT Q2 
|
Dura-Supreme Green VOB Form Release Oil, 275 gallons Vegetable oil based form release agent. VOC compliant. Environmentally safe. Part No. OTDG 
|
||||||||||||||||||||||
|
Solvent Seal 13155 Gallons A VOC-compliant, non-yellowing acrylic curing and sealing compound for all horizontal concrete floors. Cures, seals, hardens and dustproofs in one easy application. Can be used for both interior and exterior applications. Part No. SS1315 
|
Solvent Seal 131555 Gallons A VOC-compliant, non-yellowing acrylic curing and sealing compound for all horizontal concrete floors. Cures, seals, hardens and dustproofs in one easy application. Can be used for both interior and exterior applications. Part No. SS1315 55 
|
||||||||||||||||||||||
|
Alco Asphalt Foundation Coating5 Gallons Waterproof foundation coating. Part No. WP5 
|
Alco Asphalt Plastic Sealer 1405 Gallons Sealer for asphalt foundation coating. Part No. MS 5 
|
||||||||||||||||||||||
|
Uni CURE5 Gallons Cures and chemically hardens in one application. Part No. UNICURE 
|
|||||||||||||||||||||||